Jacobsen, Smithco, Turfco - Turf Equipment

Very Affordable Money saving tow-behind design with mechanical drive vacuum impeller. Highly Productive Whatever debris you collect, the V62 will collect it. From leaves to bird droppings. Trouble Free Easy to operate, easy to maintain, easy empty 4 cubic yard hopper. Light Footprint Soft-trac tires protect fine turf as well as non-turf area. Specifications Power 23HP twin-cylinder Configuration 62″ Self-contained, two-wheel, pull-type vacuum for turf and other surfaces. Pulls behind appropriate tow vehicle. Debris Hopper Capacity – 4 cubic yards | Construction – 14 gauge steel formed panels Sloped hopper bottom with 45° dump angle High capacity airflow openings at top and rear | Dump – Electric/Hydraulic open/close of tailgate to dump debris. Vacuum System 22 in diameter x 7 in wide, .25 in balanced high strength abrasion resistant impeller, 3800 CFM displacement, operating inside high strength steel housing with wear-resistant, replaceable liner, large clean out door and drain plug. Connected to sweeper head with flexible air tunnel to remove debris from ground surface and deposit into debris hopper. Tires & Wheels Rear: (2)24-1300×12 Soft-trac | Casters: (2) 9 x 3.5 x 4 Dimensions Length: 151″; Width: 68″; Height: 87″ Weight 1500 lbs

Special Feature Combination verticut/sweeper head allowing single-pass application. More Productive 7 cubic yard (5.8 cubic meter) easy-empty debris hopper and 72″ sweeper head. Vacuum Mechanical drive vacuum impeller, hydraulic drive sweeper head and verticut reels. Choice Of Sweeper Heads Rubber finger reel or combination rubber-finger verticut reel. Specifications Models 72-000 Sweep Star V72 PTO (Big Vac) Power 540-RPM Tractor PTO Input (Minimum 40hp) Dual constant Velocity drive shaft from tractor to Big Vac 5 V-Belt drive to vacuum fan Multiple V-belt drive to hydraulic pump 1 1/2″ dia. hardened steel blower drive shaft 1 1/2″ dia. hardened steel jackshaft Hydraulic power to drive motors on Sweeper-Vac head Hydraulic fluid capacity: 17 gallons Remote lubrication system Minimum 35 hp for Sweep only) operation Minimum 45 hp for Sweep and verti-cut operation Configuration 72″ Self contained, two-wheel, pull-type combination sweeper and vacuum for turf and other surfaces. Pulls behind appropriate tow vehicle Debris Hopper Capacity – 7 cubic yard Construction – Steel framework Tapered front to back for easy dumping Dump – Hydraulic raise/lower of tailgate. Hopper tailgate open/close via the mounting arm configuration. Sweeper Head Requires one of the following: 72-001 COMBINATION VERTICUT AND SWEEPER HEAD: L-78″, W- 39″, H-18″ Steel and scalp roller VERTI-CUT REEL 72″ wide Hydraulic driven from main pump to drive motor 72 hardened steel flail knives for verti-cutting SWEEPER REEL 72″ wide Hydraulic driven from main pump to drive motor 4 rows of 6″ long fingers, 24 fingers per row using roller and caster adjustments (4) adjustable caster wheels 12-600×6 pneumatic 72-002 RUBBER FINGER SWEEPER HEAD L-78″, W-18″-Height-18″ Sweeper Reel 72″ wide Hydraulic driven from main pump to drive motor 4 rows of 6″ long fingers, 24 fingers per row using caster adjustments (4) adjustable caster wheels 12-600×6 pneumatic 72-005 BRUSH REEL SWEEPER HEAD L-78″, W-18",-Height-18″ Sweeper Reel 72″ wide Hydraulic driven from main pump to drive motor (4) adjustable caster wheels 12-600×6 pneumatic Vacuum System 34″ diameter, 8 blade vacuum fan High strength steel vacuum fan housing with replaceable wear-resistant liner Clean-out hatch on fan housing connected to sweeper head with flexible air tunnel to remove debris from ground surface and deposit into debris hopper. Drive PTO drives hydraulic pump to power sweeper head and Hydraulic motor. PTO Belt drives vacuum impeller Speed Dependent on tow vehicle. Braking Relies on tow vehicles brakes. Optional: Surge Hydraulic brake package Construction Hydraulically formed, electrically welded heavy wall steel tubing. Tires & Wheels (2) 26.5-1400×12 Fairway type turf tires Controls Hydraulic raise/lower of sweeping mechanism head assembly. Electric (toggle switch) engage of vacuum impeller Sound Level 92 dbA Dimensions Length: 180" | Width: 84" | Height: 87" Weight 3500 lbs. Liquid Capacities Hydraulic System Oil: 17 gallons in steel tank Safety Fire extinguisher. Complies with all applicable ANSI, OSHA and European Machinery Directive Standards. Options 72-003 25 ft Hand-Held Vacuum Hose with Suction Nozzle | 72-004 (factory installed) Hwy package. Hwy tires, surge brakes, tail lights

Sweeper And Vacuum Mechanical drive vacuum impeller and hydraulic drive 72” sweeper head. Big Capacity Large 7 cubic yard easy-to-empty, easy -to-clean hopper. Power 35 hp twin cylinder Vanguard gasoline engine. Choice of Sweeper Heads Rubber finger reel or combination rubber-finger verticut reel. Specifications Models 73-000 Sweep Star V72E (Big Vac) Power 35 hp Twin Cylinder, OHV air cooled gasoline engine with Donaldson intake filtration, Full pressure lubrication system. Configuration 72″ Self contained, two-wheel, pull-type combination sweeper and vacuum for turf and other surfaces. Pulls behind appropriate tow vehicle. Debris Hopper Capacity – 7 cubic yard | Construction – Steel framework Tapered front to back for easy dumping. Air exhaust vents built into top of debris blower | Dump – Hydraulic raise/lower of tailgate. Hopper tailgate open/close via the mounting arm configuration. Sweeper Head 72-002 RUBBER FINGER SWEEPER HEAD L-78″, W-18″-Height-18″ Sweeper Reel 72″ wide Hydraulic driven from main pump to drive motor 4 rows of 6″ long fingers, 24 fingers per row using caster adjustments (4) adjustable caster wheels 12-600×6 pneumatic 72-005 BRUSH REEL SWEEPER HEAD L-78″, W-18″,-Height-18″, Sweeper Reel 72″ wide Hydraulic driven from main pump to drive motor (4) adjustable caster wheels 12-600×6 pneumatic Tow Hitch Options Requires on of 73-004, 73-005, OR 73-003 73-004 5th Wheel hitch for use with Textron vehicles equipped with 5th wheel hitch device and trailer brake option. 73-005 5th Wheel hitch for use with tractor 3-point hitch (Min 35 hp tractor) 73-005 5th Wheel hitch for use with tractor 3-point hitch (Min 35 hp tractor) Vacuum System 22 in diameter x 7 in. wide, 1/4”, balanced, high strength. Abrasion-resistant impeller, 3800 CFM displacement, operating inside high strength steel housing With wear-resistant, replaceable liner, large clean outdoor and drain plug. Connected to sweeper head with flexible air tunnel to remove debris from ground surface and deposit into debris hopper Drive Engine drives hydraulic pump to power sweeper head and hydraulic motor. Belt drives vacuum impeller through electric clutch Speed Dependent on tow vehicle. Braking Relies on tow vehicles brakes. Electric brakes optional, require the use of 73-004 5th wheel hitch connected to Jacobsen Turf Truckster, which is equipped with 5th wheel hitch option and electric trailer brake option Construction Hydraulically formed, electrically welded heavy wall steel tubing. Tires & Wheels (2) 26.5-1400×12 Fairway type turf tires Controls Hydraulic raise/lower of sweeping mechanism head assembly. Electric (toggle switch) engage of vacuum impeller. Increase/decrease engine speed. Remote engine start. Electrical 12-volt, electronic key start Sound Level 98 dbA Dimensions Length: 180" | Width: 84" | Height: 87" Weight 2950 lbs. Liquid Capacities Gasoline: 5 Gallons in high density nylon low-perm tank Hydraulic System Oil: 3.2 gallons in high density polyethylene tank Safety Fire extinguisher. Complies with all applicable ANSI, OSHA and European Machinery Directive Standards. Options 73-006 25 ft Hand-Held Vacuum Hose

Specifications ENGINE Power 16 HP Briggs Vanguard gasoline engine, two-cylinder, air-cooled, electronic ignition, full pressure lubrication system with replaceable filter, cast iron cylinder sleeves, engine mounted air filter. Drive Direct drive hydraulic motors eliminate the maintenance required on mechanical drive systems. Configuration A gasoline engine powered, hydraulic drive, riding golf course greens roller. Hydraulic dual roller drive system for superior traction and safety.   SPEED Infinitely variable 0 – 10 mph   BRAKES AND STEERING Braking Dynamic thru hydrostatic drive system Steering Mechanical chain/sprocket, 16” automotive type steering wheel   GREENSROLLER Construction Heavy gauge square steel tubing main frame, hydraulically formed, electrically welded Rollers Two (2) oscillating 8” x 36” length, seamless, drawn over mandrel steel tubes. Bolted hubs with bearings on each end of the rollers. Controls Keyed ignition switch, engine throttle, choke at the operator’s station. Dual drive pedals control left / right operation and rolling speed. Pedals connected to hydraulic pump via fully sealed push / pull cable system Ground Pressure 3.86 PSI Seat High back, one piece for operator comfort Electrical System 12 volt system, electric start to engine Sound Level 72 dbA under normal operating conditions Battery 12 volt Safety Dual drive roller system for superior traction and safe operation in all turf and terrain conditions. Dynamic braking thru hydrostatic drive system. Transport Trailer Low profile design with drop axle rated at 2500 lb. capacity. Extra-wide expended metal bed and tailgate fitted with rubber matting for traction and an adjustable centering guide system for easy “ load / unload “ of the roller.Width – 56”, Length – 47” tailgate “up”, not including drawbar, Weight – 240 lbs., Drawbar – adjustable from 44” to 47”, Tires – 18 -9.50×8 pneumatic Warranty Smithco two (2) year limited warranty Briggs & Stratton two (2) year engine manufacturer warranty   WEIGHTS AND DIMENSIONS Length 44" Width 45" Height 49" Weight 895 lbs Liquid Capacities Five (5) gallon fuel tank, three (3) gallon hydraulic oil tank   OPTIONS Light Kit 750-450 Greens Spiker Attachment Model 7512

Specifications ENGINE Power 16 HP Briggs Vanguard gasoline engine, two cylinder, air-cooled, electronic ignition, full pressure lubrication system with replaceable filter, cast iron cylinder sleeves, engine mounted air filter. Configuration A gasoline engine powered, hydraulic drive, riding golf course greens roller. Hydraulic dual roller drive system for superior traction and safety. Drive Direct drive hydraulic motors eliminate the maintenance required on mechanical drive systems.   SPEED Infinitely variable 0 – 9 mph   BRAKES AND STEERING Braking Dynamic thru hydrostatic drive system Steering Hydraulic power steering   GREENSROLLER Construction Heavy gauge square steel tubing main frame, hydraulically formed, electrically welded Rollers Two (2) oscillating 8” diameter x 36" length, seamless, drawn over mandrel steel tubes. Beveled on both ends with roller scrapers. Bolted hubs with bearings on each end of both rollers. Controls Keyed ignition switch, engine throttle, choke at the operator’s station. Dual drive pedals control left / right operation and rolling speed. Pedals connected to hydraulic pump via fully sealed push / pull cable system Ground Pressure 3.86 PSI Seat High back, one piece for operator comfort Electrical System 12 volt system, electric start to engine Sound Level 72 dbA under normal operating conditions Battery 12 volt Safety Dual drive roller system for superior traction and safe operation in all turf and terrain conditions. Dynamic braking thru hydrostatic drive system. Transport Trailer Low profile design with drop axle rated at 2500 lb. capacity. Extra wide expended metal bed and tailgate fitted with rubber matting for traction and an adjustable centering guide system for easy “ load / unload “ of the roller.Width – 56”, Length – 47” tailgate “up”, not including drawbar, Weight – 240 lbs., Drawbar – adjustable from 44” to 47”, Tires – 18-9.50×8 pneumatic Warranty Smithco two (2) year limited warranty Briggs & Stratton two (2) year engine manufacturer warranty   WEIGHTS AND DIMENSIONS Length 44" Width 45" Height 49" Weight 845 lbs Liquid Capacities Five (5) gallon, three (3) gallon hydraulic oil tank   OPTIONS Light Kit 750-450 Greens Spiker Attachment Model 7512

ENGINE Engine 9 HP Honda Model#: GX270UT2QA2 Commercial gasoline engine, single-cylinder, air-cooled. Engine mounted air cleaner. Drive Direct drive hydraulic motors eliminate the maintenance required on mechanical drive systems.   SPEED Infinitely variable 0 – 9 mph   BRAKES AND STEERING Braking Dynamic thru hydrostatic drive system Steering Mechanical chain/sprocket, 16" automotive type steering wheel   GREENSROLLER Construction Heavy gauge square steel tubing mainframe, hydraulically formed, electrically welded. Rollers Two (2) oscillating 8” x 36” length, seamless, drawn over mandrel steel tubes. Bolted hubs with bearings on each end of the rollers. Controls Electric start, engine throttle, choke and fuel on/off on the engine. Dual drive pedals control left / right operation and rolling speed. Pedals connected to hydraulic pump via mechanical linkage. Ground Pressure 3.35 PSI Seat High back, one piece for operator comfort Electrical System 12-volt system available from the engine while running, no battery Sound Level 90 dbA under normal operating conditions Fuel Tank 1-gallon engine mounted Oil Tank 1-gallon hydraulic oil tank Warranty Smithco two (2) year limited warranty Briggs & Stratton two (2) year engine manufacturer warranty   WEIGHTS AND DIMENSIONS Length 52" Width 49" Height 47" Weight 625 lbs   OPTIONS Light Kit 750-555 Brush Kit 7514

More Productive Three articulating rolling heads provide 70” wide rolling area. Reduce your rolling time dramatically. Easy Maintenance Direct drive to rollers eliminates time-consuming chain maintenance. Better Traction Triple hydraulic direct drive to rollers for superior traction. No time-consuming chain maintenance. Specifications ENGINE Power 16 HP Briggs Vanguard gasoline engine, two-cylinder, air-cooled, electronic ignition, full pressure lubrication system with replaceable filter. Configuration A gasoline engine powered, hydraulic drive, riding golf course greens roller. Hydraulic, triple roller drive system for superior traction and safety. Direct drive hydraulic motors to each roller cylinder eliminating the maintenance required on mechanical drive systems. Drive Hydrostatic using a 16cc hydraulic pump driving three (3) hydraulic motors direct coupled to each roller cylinder. Direct drive motors eliminate maintenance, hydraulic drive to all rollers provides superior traction in all turf and terrain conditions. Battery 12 volt   SPEED Infinitely variable 0 – 7 mph   BRAKES AND STEERING Braking Dynamic thru hydrostatic drive system Steering 10:2 Reduction; 16 soft grip steering wheel with tilt: 10 diameter turning radius; hydraulic power steering   GREENSROLLER Construction Heavy gauge square steel tubing main frame, hydraulically formed, electrically welded Rollers Two 8” diameter x 19” length and one 8 diameter x 36 seamless rollers. Controls Keyed ignition switch, engine throttle, choke at the operator’s station. Dual drive pedals control left / right operation and rolling speed. Pedals connected to hydraulic pump via fully sealed push / pull cable system. Ground Pressure 3.81 PSI with 175 lb. operator on fine turf. Seat High back, one piece for operator comfort Electrical 12 volt system, electric start to engine Sound Level 72 dbA under normal operating conditions Safety Triple drive roller system for superior traction and safe operation in all turf and terrain conditions. Dynamic braking thru hydrostat drive system. Trailer 7525 HD Transport Trailer with Clevis hitch Warranty Smithco two (2) year limited warranty Briggs & Stratton two (2) year engine manufacturer warranty   WEIGHTS AND DIMENSIONS Length 48" Width 73" Height 47" Weight 905 lbs Liquid Capacities Five (5) gallon fuel tank, Three (3) gallon hydraulic oil tank   OPTIONS Brush Kit 7513 Light Kit 750-450 Ball Hitch 750-435-1

The Turfco WideSpin™ 1550 was designed to help you achieve your agronomic goals, increase staff productivity and free up your time. With Turfco's patented hydraulic system and spinner design, along with our Smart Controller, you can be confident you're getting the application you want every time. Reduce up to 720 passes per year and minimize turf traffic to achieve the most playable, beautiful golf course. OVERVIEW The Turfco Edge started with listening to what frustrates superintendents when it comes to topdressing. We heard they were tired of doing wheel-to-wheel spreads, overlapping spreads, dealing with complicated mechanical adjustments, and wasting time checking in with their crews to verify spread settings. The WideSpin™ 1550 solves these problems, and more. Calculating and knowing your rates is easier. Adjusting settings is easier. Saving preferred settings is easier. Loading is easier. Topdressing greens, approaches and tees at the same time is easier. And getting the exact spread you want, every time, is easier. Our unique design makes it easy to get whatever width and rate you want, without having to do mechanical adjustments. You can save your preferred applications into four programmable presets, changing widths and rates on the fly, increasing productivity, eliminating guesswork and freeing up your time. WideSpin 1550 topdressers are available in truck-mounted and tow-behind models with engine or hydraulic power options. You can choose between Standard Electronic Control or upgrade to our patented digital Smart Controller. Standard Electronic Control models are easy to use and offer good value for the money. Smart Controller models offer rate calculation and programmable presets for greatest productivity and labor savings. KEY FEATURES Get the exact spread you want as you move from greens to approaches to tees, at the push of a button. Know your application rates, and determine how much material you need to budget — all for the first time ever with our on-board calculator. Reduce the number of passes and decrease traffic on your greens with WideSpin edge-to-edge applications. Drive topdressing down into the turf canopy by adjusting the spinner angle, minimizing the need for brushing and eliminating variations in spread due to moisture content (spreads the same wet or dry). Refill the hopper faster and with less spillage – galvanized hopper has 20% greater capacity and wide opening fits an 80" bucket. Three year warranty BEST SPREAD IN THE INDUSTRY For the first time ever, you can set up and save your applications one time — then get your perfect spread every time. With Turfco’s patented technologies, you can reduce greens passes, minimize turf traffic, and get a more consistent spread. REDUCED PASSES Save time and reduce wear on your greens with Turfco's patented WideSpin™ edge-to-edge technology. Decrease the number of passes on your greens by up to 720 times per year* as compared to the wheel-to-wheel method. Improve productivity and save time; unique 30-foot wide, even spread makes it possible to cover an average-size green in just two passes. Dramatically reduce traffic on your greens, reducing the potential for soil compaction and hydraulic leaks. *18 greens, 10 times a year. CALCULATE AND LOCK-IN PREFERRED APPLICATIONS Know your application rates, calculate the rates you want, and determine how much material you need to budget with our on-board calculator. Smart Controller lets you save your preferred applications into four programmable presets, allowing you to switch between widths and rates as you move from greens to approaches to tees at the push of a button. ADJUSTABLE SPINNER Drive topdressing down into the turf canopy by adjusting the spinner angle, minimizing the need for brushing and eliminating variations in moisture content (spreads the same wet or dry). LARGE HOPPER Large, galvanized steel hopper has increased capacity and is wider, making it easier to fill and less often! Refill the hopper faster and with less spillage — has 20% greater capacity and wider opening fits an 80” bucket. SPECIFICATIONS                                Model Tow-Behind 1550 Models: Engine-powered w/Smart Control (#85828); Engine-powered w/ Standard Electronic Control (#85829); Hydraulic-powered w/Smart Control (#85824); Hydraulic-powered w/Standard Electronic Control (#85825) Warranty 3 Years Engine / Models 13 HP Briggs and Stratton (engine-powered models only) Operator Control SMART: 3-position switch; 4 programmable presets; onboard rate calculator; instantaneous belt and spinner speed control; instant throttle down control (engine powered)      STANDARD Electronic: Standard 3-position switch with manual control for spinner and belt speed Weight Tow-Behind Models: Engine-powered: 1,324 lbs (601 kg);  Hydraulic-powered: 1,021 lbs (463 kg) Truck-Mounted Models: 710 lbs w/o mounting (322 Kg) Hopper Capacity 21 ft3 (0.59 m3) struck level; 25 ft3 (0.71 m3) heaped Hopper Size 80" x 36.5" (2.03 x 0.92 m) at the top Spreading Width 12' up to 40' (2.7 up to 12 m) Spread Application 0.45 ft3 per 1,000 ft3 up to 12 ft3 per 1,000 ft3 Ground Speed Up to 8 MPH (12.8 km/h) Conveyor Belt 18" (0.46 m) wide pebble surface composition with heavy-duty polyester cord Metering Gate Manually operated with Light Spread/Heavy Spread Calibrations Drive Engine Powered: Engine powered Hydraulics / Hydraulic Powered: Tow vehicle powered hydraulics Wheels 4 Ply 26.5 x 14.00 x 12 Turf (tow-behind model)

The Turfco WideSpin™ 1550 (Truck-Mounted model) was designed to help you achieve your agronomic goals, increase staff productivity and free up your time. With Turfco's patented hydraulic system and spinner design, along with our Smart Controller, you can be confident you're getting the application you want every time. Reduce up to 720 passes per year and minimize turf traffic to achieve the most playable, beautiful golf course OVERVIEW The Turfco Edge started with listening to what frustrates superintendents when it comes to topdressing. We heard they were tired of doing wheel-to-wheel spreads, overlapping spreads, dealing with complicated mechanical adjustments, and wasting time checking in with their crews to verify spread settings. The WideSpin™ 1550 solves these problems, and more. Calculating and knowing your rates is easier. Adjusting settings is easier. Saving preferred settings is easier. Loading is easier. Topdressing greens, approaches and tees at the same time is easier. And getting the exact spread you want, every time, is easier. Our unique design makes it easy to get whatever width and rate you want, without having to do mechanical adjustments. You can save your preferred applications into four programmable presets, changing widths and rates on the fly, increasing productivity, eliminating guesswork and freeing up your time. WideSpin 1550 Topdressers truck-mounted model was designed to fit all major turf vehicles. You can choose between Standard Electronic Control or upgrade to our patented digital Smart Controller. Standard Electronic Control models are easy to use and offer good value for the money. Smart Controller models offer rate calculation and programmable presets for greatest productivity and labor savings. KEY FEATURES Truck-mounted option with patented hydraulic system and spinner design fits all major turf vehicles. Get the exact spread you want as you move from greens to approaches to tees, at the push of a button. Know your application rates, and determine how much material you need to budget — all for the first time ever with our on-board calculator. Reduce the number of passes and decrease traffic on your greens with WideSpin edge-to-edge applications. Drive topdressing down into the turf canopy by adjusting the spinner angle, minimizing the need for brushing and eliminating variations in spread due to moisture content (spreads the same wet or dry). Refill the hopper faster and with less spillage – galvanized hopper has 20% greater capacity and wide opening fits an 80" bucket. Three year warranty BEST SPREAD IN THE INDUSTRY For the first time ever, you can set up and save your applications one time — then get your perfect spread every time. With Turfco’s patented technologies, you can reduce greens passes, minimize turf traffic, and get a more consistent spread. REDUCED PASSES Save time and reduce wear on your greens with Turfco's patented WideSpin™ edge-to-edge technology. Decrease the number of passes on your greens by up to 720 times per year* as compared to the wheel-to-wheel method. Improve productivity and save time; unique 30-foot wide, even spread makes it possible to cover an average-size green in just two passes. Dramatically reduce traffic on your greens, reducing the potential for soil compaction and hydraulic leaks. *18 greens, 10 times a year. CALCULATE YOUR SPREAD Know your application rates, calculate the rates you want, and determine how much material you need to budget with our on-board calculator. Smart Controller lets you save your preferred applications into four programmable presets, allowing you to switch between widths and rates as you move from greens to approaches to tees at the push of a button. ADJUSTABLE SPINNER Drive topdressing down into the turf canopy by adjusting the spinner angle, minimizing the need for brushing and eliminating variations in moisture content (spreads the same wet or dry). LARGER HOPPER Large, galvanized steel hopper has increased capacity and is wider, making it easier to fill and less often! Refill the hopper faster and with less spillage — has 20% greater capacity and wider opening fits an 80” bucket. SPECIFICATIONS <table style="border:1px solid black;border-collapse:collapse;padding:1px "> Model Hydraulic Powered (Toro, John Deere & Jacobsen); 1550 Smart Control (#85822) or 1550 Standard Electronic Control (#85823) Operator Control Smart: 3-position switch; 4 programmable presets; onboard rate calculator; instantaneous belt and spinner speed control - Standard Electronic: Standard 3-position switch with manual control for spinner and belt speed Weight 710 lbs without mounting kit (322 Kg) - Empty Weight Hopper Capacity 21 ft3 (0.59 m3) struck level; 25 ft3 (0.71 m3) heaped Hopper Size 80" x 36.5" (2.03 x 0.92 m) at the top Spreading Width 12' up to 40' (2.7 up to 12 m) Spread Application 0.45 ft3 per 1,000 ft3 up to 12 ft3 per 1,000 ft3 using patented WideSpin Technology Ground Speed Up to 8 MPH (12.8 km/h) Conveyor Belt 18" (0.46 m) wide pebble surface composition with heavy-duty polyester cord Metering Gate Manually operated with Light Spread/Heavy Spread Calibrations Drive Truck Powered Hydraulics Warranty 3 Years